This section describes the different components of Bio-Rad's real-time PCR instruments and how they can be utilized to suit your specific needs, and also provides information about the software available for analyzing the data.
Related Topics: qPCR Reagents, Assay Design and Optimization, MIQE and RDML guidelines, qPCR Data Analysis, qPCR Troubleshooting, High Resolution Melt analysis, and Primer and Probes Chemistries.
Real-time PCR detection systems consist of:
Fig. 1. Thermal gradient of the CFX96 Touch reaction block. The highest temperature is at the top and the lowest at the bottom.
Formats Reaction blocks come in multiple formats with the most common being a 96-well block (Figure 2) with reaction volumes ranging from 1 to 125 µl. Blocks with more than 384 wells typically use microfluidics with volumes in the pico to nanoliter range.
Fig. 2. Close-up view of the CFX96 Touch reaction block. This reduced-mass sample block produces fast ramping and settling, quickly reaching target temperatures.
There are a wide variety of optics systems that use a combination of light sources, filters, and detectors to measure the amount of fluorescence that is present in real-time PCR reactions.
Fig. 3. CFX96 Touch optics shuttle. Six filtered LEDs and six filtered photodiodes are used for excitation and detection. Light is filtered in a narrow bandwidth, ensuring that only data from the desired fluorophores are collected.
Fig.4. MiniOpticon™ real-time PCR detection system optics. Forty-eight LEDs fire in rapid succession, illuminating a single sample at a time, while a Fresnel lens focuses each beam directly down into the center of the corresponding well, minimizing light loss. Emitted fluorescence is split into two beams that pass through separate filters to two sensitive photodiodes.
Fig.5. iQ™5 real-time PCR detection system optics. All 96 wells are excited by a combination of narrow-bandpass filters and a tungsten-halogen lamp. Filtered light from the lamp is reflected off mirrors, passes through a condensing lens, and is focused into the center of each well. Fluorescent light emitted from the wells reflects off the main fold mirror, passes through an emission filter, and is detected by a 12-bit charge-coupled device (CCD).
Detectors Light from excited fluorophores can be detected by a stationary device (Figure 4) or from a movable one (Figure 3). There are several types of detectors that are used in real-time PCR instruments.
Fig. 6. DNA Engine Opticon® 2 real-time PCR detection system optics. The light path from the LED array to the PMT is shown.
Real-time instrument software consists of the following major components:
Protocol setup: the denaturation, annealing, and extension parameters, the number of repeated cycles, and the steps at which data are to be collected are specified (Figure 7).
Fig. 7. Protocol Editor window in CFX Manager™ software. This protocol consists of amplification followed by a melt curve to verify that a specific product has been produced.
Plate setup: The contents of each well are identified so that data can be properly analyzed once collected (Figure 8). The scan mode, which designates what channels are to be read, is also indicated.
Fig. 8. CFX96 Touch Plate Editor screen in CFX Manager software. In this screen, four different fluorophores are selected, and the sample type, sample name, and target name are indicated.
Data collection: The fluorescence intensity of the reaction mixture in each well is measured and plotted versus the reaction cycle. If a target of interest is present, its amplification can be monitored in real time (Figure 9).
Fig. 9. Run Details window in CFX Manager software. The intensity of FAM fluorescence for all wells of a 96-well plate is shown up to cycle 16.
Data analysis: Once a run is complete, a baseline is automatically calculated or can be manually set and applied to each sample so that the values obtained from different wells can be compared. A quantification cycle (Cq) is then determined for each well based on the position of a single threshold line (Figure 10) or by regression analysis.
Fig. 10. Quantification window in CFX Manager software.
Two types of analyses that are commonly performed in real-time PCR are absolute and relative quantification. Absolute quantification is achieved by comparing the Cq values of test samples to a standard curve. The result of the analysis is quantity of nucleic acid (copy number, µg) per given amount of sample (per cell, per µg of total RNA). In relative quantification, the analysis result is a ratio: the relative amount (fold difference) of a target nucleic acid for equivalent amounts of test and control sample A vs. B (Figure 11; see Real-Time PCR Experimental Design and Data Analysis for more information).
Fig. 11. Gene expression window in CFX Manager software. The normalized fold expression of three samples is shown for two targets of interest.
Call us at 1-800-268-0213
Please reenter your email address in the correct format.
Please enter your email address.
Your subscription information already exists, we will send you an email with specific instructions to manage your existing subscription profile.
To receive the latest news, promotions, and more, sign up for Bio-Rad updates by entering your email address below. You can elect to receive only the types of Bio-Rad communications that are of interest to you..
Copyright © 2014 Bio-Rad Laboratories, Inc. All rights reserved.